HiModel
KYOSHO GXR-15 ENGINE W/RECOIL STARTER FOR CARS
| Displacement | 19.96cc |
| RPM range | 3,000-19,000(r.p.m) |
| Output | 0.58/16,000(kw/r.p.m) |
| Weight | 227g |
| ① Needle value | 2 and 1/2 turns unscrewed from closed position. |
| (Caution | after each tank, allow the engine to cool off naturally!) |
, , , , , , Specifications:, , , , , , , , , , , * Note: As this engine is produced as OEM from ASP for Koyosho, the outer box you receive may with ASP marks, this is not a mistake., ● Engine starting & break-in, Adjust the needle valve and air/fuel mixture adjustment screw to their standard position as follows:, ② Air/fuel mixture adjustment: Gently screw in the idle mixture screw to closed position (clockwise); 2 and 1/2 turns unscrewed from closed position (counter clockwise), Adjustments ① ~ ② may slightly vary according to the type of glow plug and glow fuel., Proceed as follows when starting and breaking the engine in:, 1. Make sure the needle valve is unscrewed 2-1/2 turns from closed position., 2. Fill fuel into the tank. Move the throttle lever to the high position, prime the engine (push the choke button 2 to 3 times or put 2 to 3 drops of fuel directly into the carburetor) and move the throttle lever back to the slow throttle position., 3. Attach the booster cord or one-touch glow plug heater to the engine in order to electrify the glow plug., 4. Quickly pull the recoil starter rope (starter knob) several times. Only pull out 20 to 30cm of cord., (Caution: be careful not to pull out more than 50cm of cord because you may tear it and the spring inside the recoil starter!), 5. Once the engine is started, wait 5 to 10 seconds before detaching the booster cord or one-touch glow plug heater., 6. Run the engine another 2 to 3 tanks and make sure you do not apply full throttle. Also afterwards, do not increase RPM abruptly! Tighten the needle valve by 1/8 turns and continue to run the engine, handling it gently., 7. During the break-in, adjust the idle rpm with the throttle valve adjustment screw.. If rotating it clockwise (right), idle rpm increase. Idle rpm are halfway between rpm when the clutch engages and rpm when,
Includes/Requires: Includes:1 x engine 1 x manual (multi-language, including English) ...8 Reviews
HiModel
ASP 46H ENGINE FOR HELICOPTER
| Displacement | 7.45cc |
| Cylinder diameter | 22mm |
| Stroke | 19.6mm |
| RPM range | 2,000-18,000(r.p.m) |
| Weight | 390g |
, , , , , , Specifications:, , , , , , , , , , , ASP 46H Engine for Helicopters, , ,
Includes/Requires: Includes:1 x engineHiModel
ASP 15CX-H ENGINE FOR CARS W/PULL STARTER, MUFFLER - BLUE HEAD
| Displacement | 2.45cc |
| RPM range | 3,000-19,000(r.p.m) |
| Output | 0.58kw/16,000r.p.m |
| Weight | 215g / 7.6oz (with recoil starter, excluding muffler) |
| Length of output shaft | 18mm (outside) |
| Diameter of output shaft | 5mm |
| Mounting holes spacing (opposite side) | 31mm |
| Mounting holes spacing (same side) | 11mm |
| Height from Bottom of Crankcase to Top of Cylinder Head | 80mm |
| Height from Bottom Mounting Ears to Top of Cylinder Head | 68mm |
| Width at Mounting Ears | 40mm |
| Length from Back of Pull Starter to End of Crankshaft | 96.5mm |
, , , , , , Specifications:, , , , , , , , , , , *Please note that there are two versions .15 engines with same code 15CX-H (SKU, SY15CX, &, SY15CX2, ), yet the specs are quite different, please read the specs carefully and make sure you choose the right one., , ,
Features: From the most famous and professional manufacturer in China. ...6 Reviews
HiModel
ASP 15CX-H ENGINE FOR CARS W/PULL STARTER - BLUE HEAD
| Displacement | 2.45cc |
| RPM range | 3,000-19,000(r.p.m) |
| Output | 0.58kw/16,000r.p.m |
| Weight | 245.8g (with recoil starter) |
| Length of output shaft | 14mm (outside) |
| Diameter of output shaft | 5mm |
| Mounting holes spacing (opposite side) | 31mm |
| Mounting holes spacing (same side) | 11mm |
| Height from Bottom of Crankcase to Top of Cylinder Head | 86mm |
| Height from Bottom Mounting Ears to Top of Cylinder Head | 73.2mm |
| Width at Mounting Ears | 40mm |
| Length from Back of Pull Starter to End of Crankshaft | 93.8mm |
, , , , , , Specifications:, , , , , , , , , , , *Please note that there are two versions .15 engines with same code 15CX-H (SKU, SY15CX, &, SY15CX2, ), yet the specs are quite different, please read the specs carefully and make sure you choose the right one., , ,
Features: From the most famous and professional manufacturer in China. ...HiModel
ASP 32HR ENGINE FOR HELICOPTER
| Displacement | 5.26cc |
| Cylinder diameter | 19.5mm |
| Stroke | 17.6mm |
| RPM range | 2,000-18,000(r.p.m) |
| Weight | 292g |
, , , , , , Specifications:, , , , , , , , , , , ASP 32HR Engine for Helicopters, , ,
Includes/Requires: Includes:1 x engine1 Reviews
HiModel
HSP 1:10 4WD ON-ROAD NITRO POWERED CAR KIT W/ENGINE 94102
| Length | 360mm |
| Width | 200mm |
| Wheelbase | 260mm |
| Gear Ratio | 5.69 |
| Diameter of Wheel | 65*26mm |
| Engine | 15cxp |
| Thread | 195mm |
, , , , , , Specifications:, , , , , , , , , , , Height112mm, * The pattern and color of the cover may vary from the picture., *Pictures are for reference only, there are no electronic accessories come with this car., , ,
Features: This is the kit version without electronic accessories like ...HiModel
SPEED 1/10 SCALE GAS POWERED 4WD OFF-ROAD TRUCK KIT W/ENGINE 94108
| Length | 360mm |
| Width | 310mm |
| Height | 185mm |
| Wheelbase | 275mm |
| Tyre Size | 120*60mm |
| Ground Clearance | 30mm |
| Gear Ratio | 14.3 |
| Engine | 18cxp |
| Thread | 150mm |
, , , , , , Specifications:, , , , , , , , , , , *The car body cover color and pattern may different to the picture., *Pictures are for reference only, there are no electronic accessories come with this car., , ,
Features: This is the kit version without any electronic accessories. ...HiModel
KYOSHO GXR-18 ENGINE W/RECOIL STARTER FOR CARS
| Shaft length | 14mm |
| ① Needle value | 2 and 1/2 turns unscrewed from closed position. |
| (Caution | after each tank, allow the engine to cool off naturally!) |
, , , , , , Specifications:, , , , , , , , , , , * Note: As this engine is produced as OEM from ASP for Koyosho, the outer box you receive may with ASP marks, this is not a mistake., ● Engine starting & break-in, Adjust the needle valve and air/fuel mixture adjustment screw to their standard position as follows:, ② Air/fuel mixture adjustment: Gently screw in the idle mixture screw to closed position (clockwise); 2 and 1/2 turns unscrewed from closed position (counter clockwise), Adjustments ① ~ ② may slightly vary according to the type of glow plug and glow fuel., Proceed as follows when starting and breaking the engine in:, 1. Make sure the needle valve is unscrewed 2-1/2 turns from closed position., 2. Fill fuel into the tank. Move the throttle lever to the high position, prime the engine (push the choke button 2 to 3 times or put 2 to 3 drops of fuel directly into the carburetor) and move the throttle lever back to the slow throttle position., 3. Attach the booster cord or one-touch glow plug heater to the engine in order to electrify the glow plug., 4. Quickly pull the recoil starter rope (starter knob) several times. Only pull out 20 to 30cm of cord., (Caution: be careful not to pull out more than 50cm of cord because you may tear it and the spring inside the recoil starter!), 5. Once the engine is started, wait 5 to 10 seconds before detaching the booster cord or one-touch glow plug heater., 6. Run the engine another 2 to 3 tanks and make sure you do not apply full throttle. Also afterwards, do not increase RPM abruptly! Tighten the needle valve by 1/8 turns and continue to run the engine, handling it gently., 7. During the break-in, adjust the idle rpm with the throttle valve adjustment screw.. If rotating it clockwise (right), idle rpm increase. Idle rpm are halfway between rpm when the clutch engages and rpm when the engine stalls. Set idle rpm towards the lower end if possible., 8. No,
Includes/Requires: Includes:1 x engine (No English manual supplied with this ...1 Reviews
HiModel
KYOSHO GXR-28 ENGINE W/RECOIL STARTER FOR CARS
| Shaft length | 30mm |
| Displacement | 4.6cc |
| Weight | 410g |
| Mounting spacing (approx.) | 21mm same side, 39mm opposite side |
| Mounting hole diameter | 3mm |
| ① Needle value | 2 and 1/2 turns unscrewed from closed position. |
| (Caution | after each tank, allow the engine to cool off naturally!) |
, , , , , , Specifications:, , , , , , , , , , , * Note: As this engine is produced as OEM from ASP for Koyosho, the outer box you receive may with ASP marks, this is not a mistake., ● Engine starting & break-in, Adjust the needle valve and air/fuel mixture adjustment screw to their standard position as follows:, ② Air/fuel mixture adjustment: Gently screw in the idle mixture screw to closed position (clockwise); 2 and 1/2 turns unscrewed from closed position (counter clockwise), Adjustments ① ~ ② may slightly vary according to the type of glow plug and glow fuel., Proceed as follows when starting and breaking the engine in:, 1. Make sure the needle valve is unscrewed 2-1/2 turns from closed position., 2. Fill fuel into the tank. Move the throttle lever to the high position, prime the engine (push the choke button 2 to 3 times or put 2 to 3 drops of fuel directly into the carburetor) and move the throttle lever back to the slow throttle position., 3. Attach the booster cord or one-touch glow plug heater to the engine in order to electrify the glow plug., 4. Quickly pull the recoil starter rope (starter knob) several times. Only pull out 20 to 30cm of cord., (Caution: be careful not to pull out more than 50cm of cord because you may tear it and the spring inside the recoil starter!), 5. Once the engine is started, wait 5 to 10 seconds before detaching the booster cord or one-touch glow plug heater., 6. Run the engine another 2 to 3 tanks and make sure you do not apply full throttle. Also afterwards, do not increase RPM abruptly! Tighten the needle valve by 1/8 turns and continue to run the engine, handling it gently., 7. During the break-in, adjust the idle rpm with the throttle valve adjustment screw.. If rotating it clockwise (right), idle rpm increase. Idle rpm are halfwa,
Features: This is the Kyosho GXR28 engine. It has 4.6cc ...HiModel
PETROL ENGINE CDI REMOTE CONTROL SWITCH W/VOLTAGE MONITOR
| Working current | 0~4A |
| working voltage | 3V~8V |
, , , , , , Specifications:, , , , , , , , , , , Petrol engine CDI remote control switch, weight：10g(include lead wire ), Size：33mm(length) x 13mm(wide) x 13mm(high), * The round bi-color LED indicating the RX battery voltage status, not for ON/OFF status of the switch, the tiny RED LED on PCB board is for the status of the ON/OFF status of the switch., , ,
Features: This product is used to turn the remote petrol ...7 Reviews
HiModel
RCEXL OPTO GAS ENGINE KILL SWITCH
, , , , , , Specifications:, , , , , , , , , , , This device plugs into a spare receiver channel., This is a must have safety device for any gas powered plane!, This device allows you to safely kill your engine at anytime(on the ground, or in the air!), Or when out of control also allows kill the enfine., , ,
Features: This device allows you to safely and remotely kill ...4 Reviews
HiModel
PITTS MUFFER FOR GF26I/DL30 PETRO ENGINE
| Fixing bolts space | 34mm |
| Muffler interface inner size | 21 x 11mm |
, , , , , , Specifications:, , , , , , , , , , , Pitts Muffler for GF26I Petro Engine, * There is NO warranty for the pitts muffler., , ,
Features: Compatible with GF26I and DL30 engines. Includes/Requires: Includes: 1 ...4 Reviews
HiModel
PITTS MUFFER FOR GP50R/DL55/DA55 PETRO ENGINE
| Fixing bolts space | 39mm |
| Muffler interface inner size | 28 x 16mm |
, , , , , , Specifications:, , , , , , , , , , , Pitts Muffler for GP50R Petro Engine, * There is NO warranty for the pitts muffler., , ,
Features: Compatible with GP50R and DL55/DA55 engines. Includes/Requires: Includes: 1 ...3 Reviews
HiModel
DLE-30 30CC PETROL ENGINE FOR RADIO CONTROL AEROPLANE - REAR INDUCTION
| Output Power | 3.7HP at 8500rpm |
| Idle Speed | 1600 rpm |
| Static Thrust | 8.5kg at 100 meters altitude; 7.5kg at 1800 meters |
| Recommended prop size | 18x8, 18x10, 19x8, 20x8 |
| Type of the sparking plug | NGK CM6 |
| Exhaust Amount | 30.5cc |
| Bore and Stroke | 36mm×30mm |
| Compression Ratio | 7.6 |
| Carburetor | Tillotson |
| Weight | Main Engine - 910g Exhaust pipe - 60g Ignition - 120g |
, , , , , , Specifications:, , , , , , , , , , , PERFORMANCE:, Ratio of lubricating capacity: 30:1, Spare part codes:, , ,
Features: This is the new upgraded rear induction version engine. ...9 Reviews
HiModel
DLE-55 55CC PETROL ENGINE FOR RADIO CONTROL AEROPLANE
| Output Power | 5.5HP at 7500rpm (5.5HP/7500rpm) |
| Idle Speed | 1350 rpm |
| Static Thrust | 14.2kg at 100 meters altitude; 12.5kg at 1800 meters |
| Displacement | 55.6cc |
| Bore and Stroke | 45mm×35mm |
| Compression Ratio | 7.6 |
| Weight | Engine - 1310g Exhaust - 100g Ignition - 120g |
| Recommended prop size | 22×8；22×10；23×8；23×10； |
, , , , , , Specifications:, , , , , , , , , , , , ,
Features: *Due to DLE manufacturer policy change, we do not ...3 Reviews